Enterasys ANG-3000 Especificações descarregar pdf (Página 37)

Connecting XSR Cables

XSR Getting Started Guide 2-7

Connecting XSR Cables

Perform the following steps to connect your cabling:

1. Connect the serial Console cable provided in the packing box to your PC connector, as shown

in Figure 2-7.

Figure 2-7 Connecting Serial Console Cable

2. Connect your WAN cables to the T1/PRI or BRI port(s) to your WAN connectors, as shown in

Figure 2-8. Or, connect WAN cabling to your High Speed Serial connector, as shown in

Figure 2-9.

Figure 2-8 Attaching T1/PRI or BRI Port Connector

WER SUPPLY REQUIREMENTS

ETH2

ETH1

COM

NIM

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 113 114

XSR-1850 1
Getting Started Guide 1
Industry Canada Notices 4
VCCI Notice 6
BSMI EMC Statement — Taiwan 6
Australian Telecom 7
APPROVED 8
SS/366.01 8
Enterasys Networks, Inc 9
Firmware License Agreement 9
Contents 13
Appendix A: Specifications 15
Contents of the Guide 17
Getting Help 19
Overview 21
Hardware Features 22
Software Features 23
IP Routing 24
SNMP and Statistics Gathering 24
Security 25
Frame Relay 25
System Description 26
1-6 Overview 26
Quality of Service (QoS) 27
Virtual Private Network (VPN) 27
1-8 Overview 28
GRE over IPSec 29
Dial Service 29
Installation Overview 30
Hardware Installation 31
2-2 Hardware Installation 32
Figure 2-2 33
Figure 2-3 34
XSR Getting Started Guide 2-5 35
2-6 Hardware Installation 36
Connecting XSR Cables 37
2-8 Hardware Installation 38
XSR Getting Started Guide 2-9 39
2-10 Hardware Installation 40
SECURITY ROUTERS 44
Enterasys 46
Software Configuration 47
3-2 Software Configuration 48
Opening a Console Session 49
Configuring RAI over ADSL 51
PRI Configuration 54
BRI Configuration 55
BRI Leased Frame Relay 56
BRI Switched Line 56
ADSL Configuration 57
Firewall Sample Configuration 58
Setting Up RIP Routing 60
Configure OSPF Routing 61
Setting Up the Backup Line 62
Viewing Your Configuration 64
3-20 Software Configuration 66
Site regional router 67
Configure Users and Passwords 69
Configure LAN Interface 69
Configure Quality of Service 69
Apply QoS 71
Configure More Access Lists 72
Configure DHCP/BOOTP Relay 72
Branch Sites 73
Central Site 73
Set Up IKE Phase I Security 74
Create a Transform Set 75
Configure Crypto Maps 75
3-30 Software Configuration 76
3-32 Software Configuration 78
Initialization Output 79
XSR Rebooting Characteristics 80
3-34 Software Configuration 80
Reboot Triggers 81
Power-up Error Conditions 82
Bootrom Monitor Mode Commands 83
3-38 Software Configuration 84
3-40 Software Configuration 86
3-42 Software Configuration 88
Specifications 89
Category Parameters 90
Console Port 93
Ethernet Ports 94
2/4-Port Serial NIM Card Port 96
Pins not shown are unused 99
T1/E1/ISDN PRI NIM Card Ports 101
Balun for E1 or PRI NIM Cards 102
T3/E3 NIM Card 104
Port 0 Activation LED 105
Port 1 Activation LED 105
Pin 8Pin 1 105
Transmit Pair Termination 106
Port 0 Port 1 106
Receive Pair Termination 106
1/2-Port BRI-U NIM Card Ports 107
1-Port ADSL NIM Card Port 108
Regulatory/Safety Compliance 109
CompactFlash Memory Card 111
LED Behavior 111
Table A-3 LED Description 112
LED State Function 112
Index-2 114

Comentários a estes Manuais

Sem comentários

Enterasys ANG-3000 Especificações Página 37

Comentários a estes Manuais

Manuais e produtos relacionados com Gateways/controladores Enterasys ANG-3000